PRINTER REPAIR SPECAL

 

  

 

 

 

 

 

 

 

 

 

 

 

 

  

 

Following Accepted

HP PRINTER FUSER ERROR

   

 

 

 

 We Provide services to the following:

CUSTOMERS WE PROVIDED SERVICES TO:

 

HP Printer Repair

HP Laserjet Service

hp repair service

HP Officejet Pro 8500 All-in-One Printer Series (A909) -

An 'Alignment failed' Error Message Displays on the Printer

Control Panel

After you install a new printhead, the error message 'Alignment failed' displays
on the printer control panel, and an alignment page and calibration page
might print after the installation.
Figure : Example of an 'Alignment failed' error message
Image: Example of an 'Alignment failed' error message
  1. Press the Power button () to turn on the product.
  2. With the product turned on, disconnect the power cord from the rear
    of the product.
  3. Unplug the power cord from the wall outlet.
  4. Wait at least 15 seconds.
  5. Plug the power cord back into the wall outlet.
  6. Reconnect the power cord to the rear of the product.
  7. If the product does not turn on by itself, press the Power button () to turn it on.
If resetting the printer did not resolve the issue, you can watch a video to help
troubleshootthe alignment failure. The steps 
in the video are similar to but
might not match exactly the following solutions. 
The following video
demonstrates the troubleshooting steps for an 'Alignment Failed' message
that displays on your printer

This video shows the HP Officejet Pro 8500 Premier All-in-One printer, but the steps are the
same for your printer.
Follow these steps to check the alignment page that printed after the printhead installation, or try
to align the printer 
again, and then evaluate the alignment page.
Newly installed printheads must be aligned to the printer for best print quality. For successful
alignment, a sharp,
clear alignment page must print, and that requires unused, plain white
paper. Colored paper, or paper that
has already been printed on, even on the other side, can
cause the alignment to fail.
Figure : Example of a correct alignment page
Image: Example of a correct alignment page.
  • If no paper was loaded, or the paper was previously printed on or colored, or if no
    alignment page printed
    , follow these steps to retry the alignment.
    1. Load plain, white paper into the paper tray.
    2. On the printer control panel, press the Setup button ().
    3. Select Tools.
    4. Select Align Printer, and then press OK. The alignment process begins.
    5. Wait for the printer to complete the alignment, and then press OK.
    6. Check the alignment page. For successful alignment, the patterns on the
      alignment page must be sharply printed.
    • If the alignment page prints and there is no error message, the issue
      is resolved, and you can stop troubleshooting.
    • If the page is obviously faded or streaked, continue to the next solution
      to clean the printheads.
    • If you are not sure whether the alignment page printed correctly, continue
      to the next solution to print and evaluate a Print Quality Diagnostics page to
      see if the printheads are working correctly.
  • If unused, plain white paper was loaded, and an alignment page printed, check
    the alignment page. For successful alignment, the patterns on the alignment page must
    be sharply printed.
Follow these steps to clean the printheads, and then print and evaluate a Print Quality Diagnostics
page for defects.
If the alignment page was streaked or missing colors, clean the printheads.
  1. Load plain, white paper into the paper tray.
  2. On the printer control panel, press the Setup button ().
  3. Select Tools.
  4. Select Clean Printhead. The printer automatically cleans the printheads.
Follow these steps to calibrate linefeed, and then print and evaluate a Print Quality Diagnostics page.
  1. Load plain, white paper into the paper tray.
  2. On the printer control panel, press the Setup button.
  3. Select Tools.
  4. Select Calibrate Linefeed, and then press OK. The linefeed calibrates.
  1. Load plain, white paper into the paper tray.
  2. On the control panel, press the Setup button.
  3. Select Print Report.
  4. Select Print Quality Page, and then press OK. A Print Quality Diagnostics page prints.
    Figure : Example of a Print Quality Diagnostics page
    Image: Example of a Print Quality Diagnostics page
  5. Examine Test Pattern 3 for defects.
    • If the gray blocks in Test Pattern 3 show no defects, continue to the next solution to
      retry the alignment.
    • If there are still dark lines or white gaps in the gray blocks in Test Pattern 3, skip to the
      solution at the end of this document to service the printer.
      Figure : Examples of white gaps or dark lines in Test Pattern 3
      Image: Examples of white gaps or dark lines in Test Pattern 3
If there were defects on the Print Quality Diagnostics page that you corrected, follow these steps to retry the alignment.
  1. Load plain, white paper into the paper tray.
  2. On the printer control panel, press the Setup button.
  3. Select Tools.
  4. Select Align Printer, and then press OK. The alignment process begins.
  5. Wait for the printer to complete the alignment, and then press OK.
  6. Check the alignment page. For successful alignment, the patterns on the alignment page must be sharply printed.
  • If the alignment page prints and no error message displays, try another print job. If the print j
    ob is successful and no alignment page prints, the issue is resolved. You do not need to continue
    troubleshooting.
  • If the alignment page prints, and there are white lines in the color blocks in Test Pattern
    2, but no defects in Test Pattern 3
    , continue to the next solution to replace the problem printhead.
  • If the alignment page fails to print, or if a page prints and the error message displays after
    the Print Quality Diagnostics page showed no white lines in the color blocks in Test Pattern 2, skip to
    the solution at the end of this document to service the printer.
If, after repeated printhead cleaning, the Print Quality Diagnostic page shows white lines across the color
blocks in Test Pattern 2 (but no white lines in the gray blocks in Test Pattern 3), one or both of the printheads
will have to be replaced. The Print Quality Diagnostic page shows which printhead should be replaced.
Look at the color blocks labeled Test Pattern 2. Some of them should show white horizontal streaks
(if none of the blocks are streaked, the printheads are okay).
  • Black block has lines – replace the Black/Yellow printhead.
  • Red block has lines – replace the Black/Yellow printhead.
  • Green block has lines – replace the Black/Yellow printhead.
Figure : Streaked black, red, or green color blocks - replace Black/Yellow Printhead
Illustration of streaked black, red or green color blocks in test pattern 2
  • Cyan block has lines – replace the Magenta/Cyan printhead.
  • Magenta block has lines – replace the Magenta/Cyan printhead.
Figure : Streaked cyan or magenta color blocks - replace Cyan/Magenta Printhead
Illustration of streaked cyan or magenta color blocks in test pattern 2
  1. Lift the carriage-access lid. The top cover rests in an open position.
    Figure : Lift the carriage-access lid
  2. Press and hold the OK button until the carriage moves to the left side of the product. Wait for the
    carriage to stop moving.
     caution:
    Do not proceed until the carriage is on the left. If the carriage does not move to the left automatically,
    turn the printer off and back on and then try holding down the OK button again.
  3. Inside the product, lift the blue printhead latch.
    Figure : Lift the printhead latch
  4. Grasp the handle of the old printhead, and then lift upward to remove the printhead from its slot.
    Figure : Remove the printhead from its slot
  5. Without removing the replacement printhead from its packaging, rapidly shake it back and forth six times.
    Figure : Shake the printhead six times
  6. Remove the printhead from its packaging, and then remove the orange protective caps from the nozzles.
     caution:
    Do not shake the printheads after removing the orange protective caps.
    Figure : Remove the printhead and the protective nozzles
     caution:
    Do not touch the nozzles on the printhead. Touching the nozzles can permanently damage the printhead.
    Figure : Do not touch the printhead nozzles
  7. Hold the printhead by its sides with the nozzles toward the product, and then insert the printhead into its color-coded slot.
    • Insert the Black/Yellow printhead into the slot on the left.
    • Insert the Magenta/Cyan printhead into the slot on the right.
    Figure : Insert the printhead into its slot
  8. Repeat these steps if necessary to replace the other printhead. Make sure to shake the other printhead back
    and forth six times before installing it.
  9. Lower the printhead latch, and then press down until the latch snaps into place.
    Figure : Lower the printhead latch
  10. Close the carriage-access lid.
    Figure : Close the carriage-access lid
  11. Wait for the product to align the printheads and print an alignment page.
    Figure : The product prints an alignment page
Contacting HP for service in all countries/regions except Asia Pacific.
If you completed all the preceding steps and your product still has an issue, service the product.
First, go to Check your product warranty to check your printer warranty status, and then go to
t to find an authorized service dealer or to schedule a repair.
Repair fees might apply for out-of-warranty printers.

Onsite Service Appointment
Online Form

You are welcome to fill our form below and a representative will contact you to confirm the service appointment.  You can also fill out form to ask support questions or make comments.

Required fields**

 

HOME  | HP LASERJET PRINTER SPECS   |   SERVICE  |  PRINTER SALES  |  TONER CATRIDGES
SUPPORT   |   
SERVICE REQUEST  |   DIRECTORY   |   CONTACT   |  BLOG

© 2015 Titanium Print Solutions. All Rights Reservedhp printer re
pair - hp laserjet printer repair is the best pritner repair company.  how can i find a good printer repair company.  the best printer repair company.  best printer repair service.  hp laserjet pritner paper jamming.  pritner  has a 50 fsuer error.  how to rpeiar the pritner paper jam.  how to preair the hp laserejt 50 fuser error.  hp laserjet printer error.  hp laserjet pritner 49 error.  hp laserjet printer paper jam.  hp laser printer  laser printer wrinkle papers.  hp laserjet p3035 50 error.  hp color alserjet pritner.  hp pritner repzair   printer repair  printer repair  hp printer repair , hp printer repair  hp printer repair hp printer repair ii like hp printer repair color laser pritner.  hp printer service.  hp laserejet printer service. serivce hp laser prtner.  hp repair center located? onstie pritner
repair. onsite laserjet pritner  hp printer repair hp printer repair repair.  onstie printer repair.  laser pritner onstie repair center.  hp laserjet printer error 51.  onsite laser printer repair.  hp laser printer hp printer repair paper jam.  hp laserjet printer jam at the fuser.  hp color laserjet printer.  hp color laser pritner. hp color laserjjet mfp.  hp color laserjet printer adf jam.  hp color laserjet mfp not pulling paper through adf.  hp lcolor laserjet mfp adf jam.  hp laserjet mpf. hp laser printer mfp .  hp laser printer multi function printer. multifunction printer.  hp printer repair .  hp  hp laserjet printer repair  hp color laserjet printer repair  .  hp color laserjet mfp.  hp laserjet printer mfp repair  hp laser